1. Pneumatic-hydraulic supercharger cylinder system device is usually flanged fixed output piston downward device. If you need special device, please clarify before ordering, and the manufacturer can consume it according to customer's request.

2、增压缸增压系统所运用动力源为纯紧缩空气（接入前需经过过滤枯燥处置），压力为4~7kg/cm2，不得超收工作压力范围工作，(玖容厂家运用计算出力规范为6kg/cm2）。

2. The power source used in the supercharger system is pure compressed air (filtered and dried before accessing), and the pressure is 4-7 kg/cm2, which should not exceed the working pressure range. (Calculating force specification for manufacturers is 6 kg/cm2).

3、产品接入气路前，敬请先将管路及元件内的灰尘等杂物肃清，以免降低产品的运用寿命。

3. Before the product is connected to the gas pipeline, please clean up the dust and other debris in the pipeline and components so as to avoid reducing the service life of the product.

4、工作温度普通为0~60℃，如特殊工作场所请订购时注明或现场温度有变化时可向厂家寻求对应处理计划。

4. Operating temperature is usually 0-60 C. If special workplace is required, please indicate when ordering or if the site temperature changes, seek the corresponding treatment plan from the manufacturer.

5、留意运用的工作环境，不要把产品置于环境复杂如水汽重，温渡过高或过低，有化学腐蚀等。运用时要留意检查设备能否正常，日常清洁维护颐养。

5. Pay attention to the working environment, do not place the product in a complex environment such as water vapor weight, excessive or low temperature, chemical corrosion, etc. When using, we should pay attention to checking whether the equipment is normal, daily cleaning and maintenance.

6、一定要按程序操作动作程序一定要依照气路配装图的动作程序工作即预压动作-增压动作增压释压-预压复位。

6. Be sure to operate the action procedure according to the procedure, and work according to the action procedure of the gas path assembly drawing, i.e. preloading action-boosting action, boosting and releasing pressure-preloading reset.

7、增压缸系统所运用液压油为ISO VG46#,ISO VG68#抗磨液压油，添加时须留意，切勿更改成别的介质。冰冷的中央倡议运用ISO VG46#抗磨液压油，而在不是那么冷的中央如南方倡议运用ISO VG68#抗磨液压油。

7. The hydraulic oil used in the supercharged cylinder system is ISO VG46 # and ISO VG68 # anti-wear hydraulic oil. Attention should be paid when adding, and no change should be made into other media. The cold central government advocates the use of ISO VG46

8、留意液压油能否乳化蜕变，普通在运用了半年以上或者运用了500000次以上，应及时改换新的液压油以进步气液增压缸的运用寿命。

8. Pay attention to whether the hydraulic oil can emulsify and metamorphose. Generally, it has been used for more than half a year or over 500000 times. We should change the new hydraulic oil in time to improve the service life of the gas-liquid supercharger cylinder.

9、留意油桶液位的高度，当液位超出下限时会形成压力不够及行程缺乏的现象；此时应即时补充液压油。补油时须留意：液压油补给不能超出上限范围，当液压油超越上限时会形成液压油吐呈现象。正常的液压油油位为储油筒两上下线之间，不宜过多或过少。

9. Pay attention to the height of the oil barrel, when the liquid level exceeds the lower limit, there will be insufficient pressure and lack of travel. At this time, the hydraulic oil should be replenished immediately. When replenishing oil, we should pay attention to: hydraulic oil replenishment can not exceed the upper limit, when the hydraulic oil exceeds the upper limit, it will form the phenomenon of hydraulic oil vomiting. The normal hydraulic oil level is between the upper and lower lines of the storage tank, so it should not be too much or too little.

10、为到达佳的空气质量，倡议选用自动排水型的三点组兼并及时加油光滑及排水处置。留意三点组合之排水功用能否正常，若失效，则用手动方式定时排水或改换新产品。

10. In order to achieve the best air quality, it is advocated to choose automatic drainage three-point group merger and timely refueling, smoothing and drainage disposal. Pay attention to whether the drainage function of the three-point combination is normal or not. If it fails, it will drain regularly or replace new products manually.

11、为达佳出力效果，倡议在增压缸与三点分离之间增加一储气设备，保证有足够稳定的气源气压供增压系统运用。

11. In order to achieve the best output effect, it is proposed to add a gas storage device between the supercharger cylinder and the three-point separation to ensure that there is enough stable air pressure for the use of the supercharger system.

12、倡议在增压段的进气口前加装一个附逆止型调压阀，以降低输出压力,即到达所需的工作出力即可，以免出力太大糜费耗材，降低模具寿命并可俭省能源。

12. It is proposed to install a backstop pressure regulating valve before the inlet of the boosting section to reduce the output pressure, i.e. to reach the required work output, so as to avoid wasting material too much, reduce the life of the die and save energy.

13、停机未工作时应将机台压力释放及切断电源，减少耗费能源及延长产品寿命。

13. When shutdown is not in operation, the pressure of the machine should be released and the power supply should be cut off to reduce energy consumption and prolong the life of the product.