开云在线官方

网站公告:

新闻中心

开云在线官方(中国)有限公司官网

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址://keonnected.com

企业动态

当前位置:首页 - 新闻中心 - 企业动态 - 高压气体增压泵安装的六个

高压气体增压泵安装的六个步骤

发布时间:2019-03-30 10:39:30   发布人://keonnected.com
  气体增压泵又称空气增压泵,在流体控制行业中应用非常广泛,高压气体增压泵可以将一般气体的压力提高100倍达到高压气体,以达到工作的目的。
  Gas booster pump, also known as air booster pump, is widely used in fluid control industry. High pressure gas booster pump can increase the pressure of general gas by 100 times to achieve high pressure gas, so as to achieve the purpose of work.
  1. 安装高压气体增压泵
  1. Install high pressure gas booster pump空气压力阀标签配有两个开槽安装支架。压力阀可以安装在任何位置。建议的位置是垂直的。
  The air pressure valve label has two slotted mounting brackets. The pressure valve can be installed in any position. The recommended position is vertical.
气体增压泵
  2. 预空气供应的连接
  2. Connection of pre air supply
  高压气体增压泵本体标注“进口”,图纸标注端口尺寸及型号。预加气必须是纯气,如果介质中有油库可能会损坏高压元件,导致增压阀工作失灵,所以建议在增压阀进口处安装过滤器。
  High pressure gas booster pump body shall be marked with "inlet", and port size and model shall be marked on the drawing. The pre filling gas must be pure gas. If there is oil depot in the medium, the high-pressure components may be damaged, resulting in the failure of the booster valve, so it is recommended to install a filter at the inlet of the booster valve.
  3.气源连接
  3. Air supply connection
  安装供气回路时,应尽量将过滤器/调压阀打入增压阀内。进气口为g1/4”,阀体标注“驱动口”,管径为1/2”。如果管径较小,则增压阀不能以流量运行。过滤器调节阀应按名称连接,靠近升压阀。
  When installing the air supply circuit, try to drive the filter / pressure regulating valve into the booster valve. The air inlet is G1 / 4 ", the valve body is marked with" drive port ", and the pipe diameter is 1 / 2". If the pipe diameter is small, the booster valve cannot operate at the maximum flow. The filter regulating valve shall be connected according to the name, close to the booster valve.
  4. 的消声器
  4. Muffler
  消声器用于降低增压阀运行时的噪声,保证运行环境的安静。排气口端口为g1/2”,标记为“排气口”。
  The muffler is used to reduce the noise of the booster valve during operation and ensure the quiet operation environment. The vent port is G1 / 2 "marked" vent. ".
  5. 高压气体出口连接
  5. High pressure gas outlet connection
  增压阀的示意图上标明了端口尺寸和型号。阀体标记为“出口”,是一个高压出口。因此,在连接时需要特别小心。
  The port size and model number are indicated on the schematic of the boost valve. The valve body is marked "outlet" and is a high pressure outlet. Therefore, special care is required when connecting.
  6. 高压气体增压泵启动
  6. High pressure gas booster pump starts
  (1)打开增压阀进口开关前,使用调节减压阀将压力设置为“0”PSI,以保证所有连接、所有部件和安装。
  (1) Before opening the boost valve inlet switch, use the regulator to set the pressure to "0" psi to ensure all connections, all components and installation.
  现在慢慢调整减压阀,直到升压阀启动。正常情况下,升压阀是15-20 psi的气动压力。
  Now slowly adjust the pressure reducing valve until the pressure increasing valve is started. Normally, the boost valve is a 15-20 psi pneumatic pressure.
  完成步骤1至3后,调整泵的气压,直到系统要求的输出压力是气体增压泵的相关内容,开云在线官方对您有所帮助。
  After completing steps 1 to 3, adjust the air pressure of the pump until the required output pressure of the system is related to the gas booster pump. I hope it can help you.
 
新闻推荐:
空气增压泵的使用优势大揭秘! 2022-07-05
气体增压泵的生产要注意哪些环节? 2022-06-27
选择气动增压泵要从哪些方面考虑? 2022-06-19
大流量气体增压系统的使用特点 2022-06-10
气体增压泵一直被长期使用的原因? 2022-06-02
气体增压泵和液体增压泵有什么区别? 2022-05-27
气体增压泵能取代传统的机械泵、液压泵 2022-05-15
增压泵的安装必要事项! 2022-05-10
增压泵的使用维护非常简单! 2022-04-28
气体增压泵的使用方法及注意事项: 2022-04-20

13188935873