气体增压泵顾名思义是增压气体的增压泵，其原理是利用低压气体推动大活塞来带动高压增压缸的小活塞，通过大小活塞的面积比来得到气体增压泵的增压比。为什么说气体增压泵的使用对多个方面有要求呢？

As the name implies, the gas booster pump is a booster pump of pressurized gas. Its principle is to use the low-pressure gas to push the large piston to drive the small piston of the high-pressure booster cylinder, and obtain the booster ratio of the gas booster pump through the area ratio of the large and small pistons. Why is the use of gas booster pump required in many aspects?

1.使用方要准备好被增压气体和管路，驱动气体和管路，高压气体的出口管路，按增压泵出厂时所带的说明书先固定增压泵，按照增压泵的各个进出口接头尺寸，连接好管路，检查是否耐压足够，接头是否有泄露等，检查完好后就可以进行增压测试了。

1. The user shall prepare the pressurized gas and pipeline, the driving gas and pipeline, and the outlet pipeline of high-pressure gas. Fix the booster pump according to the instructions provided by the booster pump when it leaves the factory. Connect the pipeline according to the size of each inlet and outlet connector of the booster pump. Check whether the pressure resistance is sufficient and whether the connector is leaking. After the inspection is complete, the booster test can be carried out.

2.气源方面：气体增压泵的驱动气源一般是在1.8-8bar压力范围，不建议它的驱动气源超过10bar，如果驱动气源过高，那么很大程度上会对泵体造成损伤，更有甚者会对操作人员造成人员伤亡

2. Air source: the driving air source of the gas booster pump is generally in the pressure range of 1.8-8bar. It is not recommended that its driving air source exceed 10bar. If the driving air source is too high, it will damage the pump body to a large extent, and even cause casualties to the operators

3.气体增压泵选型方面：客户要根据自身的压力选择对应的增压比，按照客户自己的压力需求，突出气源压力、进气压力、输出压力需求、流量是多少，销售工程师才能更准确的帮您选型

3. Selection of gas booster pump: customers should select the corresponding boosting ratio according to their own pressure. According to their own pressure demand, focus on the gas source pressure, intake pressure, output pressure demand and flow. Only then can the sales engineer help you select the type more accurately

4.对现场使用环境方面：现场使用环境一定要干净，不能有太大的粉尘颗粒状，驱动气源及被增压介质水分不要含量太多，这样会大大降低泵的使用的寿命；

4. For the on-site use environment: the on-site use environment must be clean without too much dust particles. The water content of the driving air source and the pressurized medium should not be too much, which will greatly reduce the service life of the pump;

5.对管路的要求：客户现场使用的时候一定要检测高压输出管道的密封严实型，采用的管道、阀门、压力表一定要大于气体增压泵输出的额定压力。大限度的保证人员的操作安全；

5. Requirements for pipeline: when the customer uses the pipeline on site, the tightness of the high-pressure output pipeline must be tested. The pipeline, valve and pressure gauge used must be greater than the rated pressure output by the gas booster pump. Ensure the operation safety of personnel to a large extent;

6.对压力容器的要求：各部分承压件，特别是压力容器，一定要具有压力安全容器厂家生产的压压力安全容器检查报告。

6. Requirements for pressure vessels: all pressure containing parts, especially pressure vessels, must have the inspection report of pressure safety vessels produced by the pressure safety vessel manufacturer.

此外气体增压泵适合的场合非常普遍如气弹簧冲氮气，工业用氧气激光切割，反应釜二氧化碳超临界等所有用到无腐蚀性气体增压的领域都可以使用。更多相关内容就来我们网站//keonnected.com咨询了解吧！

In addition, the gas booster pump is suitable for a wide range of applications, such as gas spring charging nitrogen, industrial oxygen laser cutting, reaction vessel carbon dioxide supercritical and so on. It can be used in all fields where non corrosive gas pressurization is used. For more information, please visit our website //keonnected.com Consult and understand!