如果您发现增压泵在没有水的情况下不停止工作，可能是以下原因造成的：
If you find that the booster pump does not stop working without water, it may be caused by the following reasons:
1、可能是停机压力值设置过高。如果停机压力设置过高，无论有无水，增压泵都无法达到设定压力，自然不停机。
1. The shutdown pressure may be set too high. If the shutdown pressure is set too high, no matter there is no water, the booster pump cannot reach the set pressure and will not shut down naturally.
解决方法：如果有指针压力表，先看电流不停止时指针压力指示的位置，记下压力值，然后检查对应的设定停止压力值（仅针对可以自己设置）。压力值），适当降低设定的停机压力值，然后重试。
Solution: if there is a pointer pressure gauge, first look at the position indicated by the pointer pressure when the current does not stop, write down the pressure value, and then check the corresponding set stop pressure value (only for self setting). Pressure value), reduce the set shutdown pressure value appropriately, and then try again.
2、单向阀漏水。单向阀的作用是防止已经加压的水的压力倒流，造成压力下降。如果单向阀密封不好导致漏水，则无法达到设定的上限，泵也不会停止。
2. The check valve leaks. The function of one-way valve is to prevent the pressure backflow of pressurized water, resulting in pressure drop. If the one-way valve is not well sealed, resulting in water leakage, the set upper limit cannot be reached, and the pump will not stop.
解决方法：先将增压泵加压到一定值，记下该值，然后关闭增压泵电源，观察指针是否会下降，如果下降则表示漏水。如果没有压力表，只能停一会，然后打开水龙头，看看水压有没有明显下降。
Solution: first pressurize the booster pump to a certain value, write down the value, then turn off the power supply of the booster pump, and observe whether the pointer will fall. If it falls, it means water leakage. If there is no pressure gauge, you can only stop for a while, and then turn on the tap to see if the water pressure drops significantly.
3、其他水管有漏水现象。管网其他水点漏水也会导致压力持续下降，达不到设定的停机压力值。
3. Other water pipes are leaking. Water leakage at other water points in the pipe network will also cause the pressure to continue to drop and fail to reach the set shutdown pressure value.
解决方法：这种可能性不大，但还是要观察是否有泄漏。
Solution: This is unlikely, but it is still necessary to observe whether there is leakage.
4、增压泵的控制器或传感器坏了。如果经过以上3个步骤仍然无效，则可能是增压泵的控制器或传感器坏了。
4. The controller or sensor of the booster pump is broken. If the above three steps are still invalid, the controller or sensor of the booster pump may be broken.
解决方法：这种性比较强，一般不要在没有厂家指导的情况下轻开云在线官方试，有触电的危险。
Solution: this kind of specialty is relatively strong. Generally, it is not easy to test without the guidance of the manufacturer. There is a risk of electric shock.
另外，达到压力平衡后，泵自动停机，采用单气控不平衡配气阀，实现泵的自动往复运动。泵体气动部分采用铝合金制造。与液体接触的部件根据不同介质采用碳钢或不锈钢制造，泵的全套密封件均采用进口优质产品，从而保证了
气液增压泵的性能。
In addition, when the pressure is balanced, the pump will stop automatically, and a single pneumatic unbalanced valve is used to realize the automatic reciprocating motion of the pump. The pneumatic part of the pump body is made of aluminum alloy. The parts in contact with liquid are made of carbon steel or stainless steel according to different media, and the full set of seals of the pump are imported high-quality products, so as to ensure the performance of the gas-liquid booster pump.
The reason why the booster pump doesn't stop working without water is this. If you have other problems, please follow our website //keonnected.com Come on!
