正确的安装增压泵可以延长增压泵的使用寿命，安装前需要仔细查看增压泵有没有异常问题，是否有磨损或者配件出现损坏。总之气液增压泵的安装需多加了解一些要点，下面来进行更为详细的讲解。

The correct installation of the booster pump can prolong the service life of the booster pump. Before installation, carefully check whether the booster pump has any abnormal problems, whether there is wear or whether the accessories are damaged. In a word, the installation of gas-liquid booster pump needs to know more about some key points, which will be explained in more detail below.

（1）安装位置要保持一致，距离水位的位置要有一定的要求，尽量安装在水位较低的位置，这样方便以后的维修与使用。

(1) The installation position shall be consistent, and there shall be certain requirements for the position away from the water level. The installation shall be at a lower water level as far as possible, so as to facilitate future maintenance and use.

（2）装好后需要查看管道的连接处是否紧密，是否有气体泄露，这样可以确保达到密封性能的要求，假如出现了漏气情况会造成抽不上水的情况。

(2) After installation, it is necessary to check whether the connection of the pipeline is tight and whether there is gas leakage, so as to ensure that the requirements for sealing performance can be met. If there is gas leakage, it will cause water pumping failure.

（3）增压泵使用时功率较大，建议选择一条单一的线路，接着要安装保护器装置，避免超过了一定负荷造成出现断路的情况。（4）为了确保安全需要连接地线，并且选择三芯安全插座。

(3) The booster pump has a large power when it is used. It is recommended to select a single line, and then install a protector device to avoid a circuit break caused by exceeding a certain load. (4) To ensure safety, it is necessary to connect the ground wire and select a three core safety socket.

（5）使用过程中，假如发现增压泵出现了漏水的问题，需要先切断电源，接着再排查增压泵中有没有一些堵塞物，再逐一进行清理。

(5) In the process of use, if the booster pump is found to have water leakage, the power supply should be cut off first, and then check whether there are any blockages in the booster pump, and then clean them one by one.

（6）气液增压泵应该安装在室内或者有遮挡的户外场合，环境温度在5℃～40℃，湿度小于90%，应该有良好的通风性，周围不可以有腐蚀性液体或者气体，增压泵适用场合不能超过2000m。

(6) The gas-liquid booster pump should be installed indoors or in sheltered outdoor places. The ambient temperature is 5 ℃~40 ℃, and the humidity is less than 90%. It should have good ventilation. There should be no corrosive liquid or gas around. The booster pump should not be more than 2000m in applications.

（7）增压泵须确保安装保持在水平状态，否则会发生机械故障。移动时需要轻拿轻放，否则会造成底板出现破损。

(7) The booster pump must be installed in a horizontal state, otherwise mechanical failure may occur. It needs to be handled with care when moving, otherwise the bottom plate will be damaged.

以上就是小编为您讲解的关于气液增压泵的安装需多加了解一些要点的相关内容了。您对此有什么疑惑或者需求都可以来我们网站//keonnected.com进行咨询了解！

The above is the related content about the installation of the gas-liquid booster pump that I have explained to you. You can come to our website if you have any doubts or needs //keonnected.com Ask about it!