气体增压泵顾名思义是增压气体得增压泵，其原理是利用低压气体推动大活塞来带动增压缸得小活塞，通过大小活塞得面积比来得到气体增压泵得增压比，如大小活塞得面积比为10:1得话，那么增压后得气体会和驱动气体成10倍得关系，其增压缸和驱动缸是分开得，所以被增压气体得纯度不会受到其它影响而降低纯度。

The gas booster pump, as its name implies, is a booster pump for pressurized gas. Its principle is to use low-pressure gas to drive the large piston to drive the small piston of the booster cylinder. The pressurization ratio of the gas booster pump is obtained by the area ratio of the large and small pistons. If the area ratio of the large and small pistons is 10:1, then the pressurized gas will have a 10 times relationship with the driving gas, and the booster cylinder and the driving cylinder are separated, Therefore, the purity of the pressurized gas will not be affected by other factors to reduce the purity.

气体增压泵使用方法也比较简单，使用方要准备好被增压气体和管路，驱动气体和管路，高压气体得出口管路，按增压泵出厂时所带得说明书先固定增压泵，按照增压泵得各个进出口接头尺寸，连接好管路检查是否耐压足够，接头是否有泄露等，检查完好后就可以进行增压测试了。

The use method of the gas booster pump is also relatively simple. The user should prepare the pressurized gas and pipeline, the driving gas and pipeline, and the outlet pipeline of the high-pressure gas. Fix the booster pump according to the instructions provided by the booster pump when it leaves the factory. Connect the pipeline according to the size of each inlet and outlet connector of the booster pump to check whether the pressure is sufficient and whether the connector has leakage. After the inspection is complete, the booster test can be carried out.

气体增压泵使用的时候，要调节驱动气压≤3-8bar，驱动气压经济使用压力是6bar，另外驱动气压要保持洁净、干燥、无水分，这样才能是增压机的驱动缸体及换向阀保证运行正常，密封圈寿命更加长久!

When the gas booster pump is used, the driving air pressure should be adjusted to ≤ 3-8bar, and the economic operating pressure of the driving air pressure is 6bar. In addition, the driving air pressure should be kept clean, dry, and free of moisture, so that the driving cylinder body and reversing valve of the booster can operate normally, and the life of the sealing ring can be longer!

气体增压泵增压部分IN(入口)压加装过滤器，保证被增压气体介质的洁净，起到二次保护的作用，另外高压出口如果压力过高，提议加装爆破片等防护措施。如高压出口需要配置缓冲罐体则要购买承压值要高于泵体的额定输出压力压力容器(具有压力容器证书)。

The IN (inlet) of the pressurizing part of the gas booster pump is pressed with a filter to ensure the cleanliness of the pressurized gas medium and play a role of secondary protection. In addition, if the pressure at the high-pressure outlet is too high, it is proposed to install bursting discs and other protective measures. If a buffer tank is required at the high-pressure outlet, a pressure vessel with a pressure bearing value higher than the rated output pressure of the pump shall be purchased (with a pressure vessel certificate).

在气体增压泵再进行维护的时候，要在没有气压情况下进行维护，关闭驱动、关闭进气压力，卸荷高压输出压力再进行维护保养。另外建议与技术人员进行沟通或者视频指导下进行维护。

When the gas booster pump is to be maintained again, the maintenance shall be carried out without air pressure, the drive shall be closed, the inlet pressure shall be closed, and the high-pressure output pressure shall be unloaded for maintenance. In addition, it is recommended to communicate with technicians or conduct maintenance under video guidance.

气体增压泵适合得场合非常普遍如气弹簧冲氮气，工业用氧气激光切割，反应釜二氧化碳超临界等所有用到无腐蚀性气体增压得领域都可以使用。更多相关设备产品的内容了解就来我们网站//keonnected.com咨询吧！

The gas booster pump is suitable for very common occasions, such as nitrogen flushing by gas spring, oxygen laser cutting for industrial use, carbon dioxide supercritical reaction kettle, and all fields that use non corrosive gas pressurization can be used. For more information about related equipment products, please come to our website //keonnected.com Consult!